What Hub Dimensions Should A Motorcycle Brake Disc RFQ Include?

Nov 16, 2026

Leave a message

Two motorcycle brake discs can share an outside diameter and bolt count yet sit in different positions when bolted to the wheel. A useful request for quotation (RFQ) should show what locates the disc, what it seats against, and where the middle of its friction track must sit relative to that seating face. Include a face view and a section through the axle so the supplier can check both the bolt pattern and the axial position.

Identify the Wheel Build You Are Quoting

Start with the motorcycle model and variant, front or rear wheel, and left or right side where applicable. Include the identifiers and revisions for the hub, disc, caliper bracket, and any ring or spacer that shares the interface. If buyers use the same sales model name for two wheel builds, quote each build separately until engineering confirms that the disc interface is shared.

When the inquiry starts with a used disc, label any measurements as reference data. Wear can change the measured friction thickness, and a loose disc cannot show which mating face or locator the assembled wheel uses. Send a hub drawing or an annotated section of the assembly alongside the sample, and have the design owner confirm dimensions that the sample cannot establish.

Show What Seats and Locates the Disc

Distinguish the Locating Feature From a Clearance Opening

Mark the face that actually contacts the wheel hub. Show the diameter and depth of the locating register if one is used, along with the matching shoulder or recess. If the center opening merely clears another feature, indicate which features do locate the disc. Include nearby fillets or reliefs where they affect seating. The correct bore diameter alone does not tell a supplier whether a shoulder will bottom out before the disc reaches the hub face.

Define the Full Bolt Pattern and Seats

Show the bolt circle diameter, hole count, individual hole sizes, and the orientation of any uneven pattern or indexing feature. Distinguish the disc's clearance holes from threads in the hub. Identify the fastener head seat, any recess or spotface, and the mating hardware. A matching bolt pattern can still leave a head standing proud of the carrier or a seat that does not match the specified fastener.

Dimension the Friction Track From the Hub Face

On the section view, mark the hub mating face, both friction faces, and their midpoint. Give the distance from the mating face to that midpoint and show which direction is positive, such as toward the wheel center. If a supplier quotes an offset measured to one friction face or gives the overall disc height, ask for a cross section that puts both definitions on the same reference. Those numbers cannot be compared reliably by label alone.

Specify the thickness and tolerance of a new disc and the inner and outer limits of the usable friction track. Ask engineering to check where the pad contacts that track on the assembled wheel. Keep any in-service wear limit separate from the dimensions used to accept a new part. A sample that bolts to the hub still needs review for axial alignment and pad contact.

Check What Shares the Mounting Space

Use the same wheel section to show nearby parts, then ask the supplier to flag assumptions about what is included in the quote. A dimension belongs to a specific assembly configuration; adding a ring or changing the carrier may change the stack even if the hole pattern stays the same.

Interface What to confirm
Fastener seats Head and washer envelope relative to the hub and nearby parts
Speed sensor ring, if fitted Mounting face, position in the stack, and clearance to the sensor for that wheel build
Floating disc carrier, if specified Carrier and bobbin envelope and the specified range of movement
Caliper and pads Track alignment, pad coverage, and clearance to the carrier and fasteners

Separate Part Inspection From Mounted Runout

Agree which dimensions will be checked on a loose disc and which require the assembled wheel. Name the drawing revision, units, reference features, and applicable drawing convention. The ASME Y14 standards list identifies Y14.5 as a reference for geometric dimensioning and tolerancing. Use the convention and edition specified by the project to interpret the callouts.

Lateral runout describes how far the friction face moves axially at the measurement point as the assembly rotates. A mounted reading reflects the assembled condition, including the hub face and how the disc is seated. Specify the intended fixture or wheel build, assembly conditions, measurement radius, and acceptance limit in the inspection plan. Kawasaki's Ninja service manual illustrates a dial gauge check on a rotating wheel for a specific application. Use your project's approved limits and method for sample acceptance.

Ask for an Annotated Supplier Response

A quotation should make it easy to see whether both teams are reading the interface the same way. Ask for these four items alongside the price:

  • A marked drawing or section showing the locating feature and the face that seats on the hub.
  • The proposed bolt and seating details, with the offset shown to the friction track midpoint.
  • A list of included and excluded hardware, plus any dimensions the supplier still needs.
  • A proposed inspection split between the loose disc and the assembled wheel.

Use Zhanxiang's motorcycle brake disc product page as a starting point for an inquiry. Send the wheel build and the annotated section together so the supplier can answer the fit questions before making samples. Have the vehicle engineering team confirm assembly fit and the required brake validation before release.

Send Inquiry