Hey there, fellow motorcycle enthusiasts! As a supplier of Brake Cylinder Motorcycle, I've seen firsthand how important it is to keep your bike's brakes in top - notch condition. One crucial maintenance task that often gets overlooked is bleeding the air from the motorcycle brake cylinder. In this blog, I'll walk you through the process step - by - step.
Why Bleeding the Brake Cylinder is a Big Deal
First off, let's talk about why you need to bleed the air from your brake cylinder. Air in the brake lines can cause a spongy or soft brake lever feel. You press the brake, but it doesn't respond as quickly or forcefully as it should. This is super dangerous because it can seriously affect your stopping power when you're out on the road.
Brakes work on a hydraulic system. When you squeeze the brake lever, it pushes brake fluid through the lines, which then activates the brake calipers to clamp down on the rotors. But if there's air in the lines, air is compressible while brake fluid isn't. So, when you press the lever, the air compresses instead of transferring the force to the calipers. That's why you end up with a weak brake response.
Tools You'll Need
Before you start bleeding the brakes, gather these tools:
- A clear plastic tube that fits snugly over the bleeder valve.
- A container to catch the old brake fluid.
- A wrench that fits the bleeder valve.
- Fresh brake fluid. Make sure it's the right type for your motorcycle. Check your owner's manual for this info.
- A clean rag to wipe up any spills.
Step - by - Step Guide to Bleeding the Brake Cylinder
Step 1: Prepare Your Bike
Park your motorcycle on a level surface. It's important that the bike is stable so that the brake fluid level remains consistent. Make sure the engine is off and the bike has cooled down. You don't want to burn yourself on a hot engine or exhaust.
Open the brake fluid reservoir. It's usually located near the brake lever on the handlebars for the front brakes or near the foot - pedal for the rear brakes. Check the fluid level. If it's low, top it up with fresh brake fluid. But don't overfill it.
Step 2: Locate the Bleeder Valve
The bleeder valve is a small screw - like valve on the brake caliper. It's usually on the top or side of the caliper. On some bikes, it might be a bit hard to reach, so you may need to use a mirror to spot it.
Step 3: Attach the Plastic Tube
Take the clear plastic tube and fit one end tightly over the bleeder valve. Put the other end of the tube into the container that will catch the old brake fluid. This way, you can see the air bubbles coming out and the old fluid being replaced.
Step 4: Start Bleeding
Now, have a friend sit on the bike and hold the brake lever firmly. If you're working on the rear brakes, they'll need to press the foot - pedal. While they're holding the brake, use the wrench to loosen the bleeder valve a little bit. You'll see air bubbles and old brake fluid start to flow through the tube into the container.
Keep an eye on the fluid level in the reservoir. As you're bleeding the brakes, the level will drop. Make sure to top it up with fresh brake fluid as needed to avoid introducing more air into the system.
Step 5: Repeat the Process
Once the air bubbles stop coming out and the fluid flowing through the tube looks clean, close the bleeder valve tightly. Then, have your friend release the brake lever or pedal. Repeat this process of squeezing the lever, opening the valve, and closing it again several times until you're sure all the air is out. You can tell when the brake lever feels firm and responsive.
Step 6: Final Checks
After you're done bleeding the brakes, double - check the fluid level in the reservoir and top it up if necessary. Make sure all the bleeder valves are tightened properly. Wipe up any spilled brake fluid with a clean rag.
Now, test the brakes. Squeeze the lever or press the pedal a few times. The brakes should feel firm and engage quickly. If the brakes still feel spongy, you may need to repeat the bleeding process.


Our Brake Cylinder Products
As a Brake Cylinder Motorcycle supplier, we offer a wide range of high - quality brake cylinders. For example, our Supermoto Front Brake Master Cylinder is designed for optimal performance. It's built with precision to ensure smooth and efficient brake operation.
Another great product is our Motorcycle Master Cylinder ZX - 1051. This master cylinder is known for its durability and reliability. It can withstand the rigors of daily riding and even more intense off - road adventures.
And if you're looking for a different option, our Motorcycle Master Cylinder ZX - 1046 is also a top - notch choice. It provides excellent braking power and is easy to install.
Contact Us for Purchasing
If you're in the market for a new brake cylinder or have any questions about our products, don't hesitate to get in touch. We're here to help you find the perfect brake cylinder for your motorcycle. Whether you're a casual rider or a professional racer, our products are designed to meet your needs.
References
- Motorcycle Owner's Manuals
- Motorcycle Maintenance Guides from Reputable Publishers

